Products Page

ISM43340-M4G-L44 Serial-to-WiFi & BLE Combo Module

The ISM43340-M4G-L44 is an embedded 2.4 & 5 GHz Wi-Fi 802.11 a/b/g/n, Bluetooth Low Energy (BLE) and Bluetooth 4.0 module. The module hardware consist of a Broadcom BCM43340 Combo radio, antenna and a STM32F405 host processor with 1MB of flash and supports SPI or UART host interfaces.

The Wi-Fi module requires no operating system and has an integrated TCP/IP stack that only requires a simple AT command set to establish connectivity for your wireless product. The module has a small 14.70mm x 34.22mm surface mount footprint and has full FCC and CE module certification. This product is targeted for low cost embedded wireless applications and enables a quick, easy and cost effective method adding WiFi, Bluetooth, and BLE connectivity to your platforms.

Key module features:

  • 802.11 b/g/n Broadcom BCM43340 Radio device
  • Bluetooth 4.0 with support for Wi-Fi /BLE  co-existence
  • Fully contained TCP/IP stack thus minimizing host CPU requirements
  • Configurable though AT commands
  • Host interface: UART, SPI up to 25+ MHz
  • Network features ICMP ( Ping), ARP, DHCP,TCP, UDP
  • BLE, Bluetooth 4.0
  • Over the Air updates (OTA)
  • Secure WiFi authentication WEP-128, WPA-PSK (TKIP), WPA2-PSK 

Product Documentation

Technical Resources

Product Resources

Firmware

Software Scripts Examples

Evaluation Board

Evaluation Board. The EVB supports all eS-WiFi modules in the L44 and L44+10 (Land Grid Array) footprint – ISM43362, ISM4390, ISM43340, ISM43341, ISM4343 and ISM907
ISM43362-M3G-EVB-E311
ISMART (Inventek Systems Module Arduino Test) IoT platform ISMART43340-C Arduino Shield
ISM43340C Shield part

Buy Online from Our Valued Distributors

Buy Inventek products from DigiKey
Buy Inventek products at Avnet
Buy Inventek products from Texim Europe
Buy Inventek products from Macnica Store

Contact Inventek

For sales technical support distribution Volume Pricing and delivery options
Contact Inventek

ISM43362-M3G-L44-E/U Serial-to-WiFi Module

The ISM43362-M3G-L44-E/U is an embedded 2.4 GHz  Wi-Fi  module. The Wi-Fi module hardware consists of a Cypress BCM43362, an integrated antenna or optional external antenna, and a STM32F205 host processor that has a standard SPI or UART interface capability.

The Wi-Fi module requires no operating system and has an integrated TCP/IP stack that only requires a simple AT command set to establish connectivity for your wireless product. The module has a very small 14.5mm x 30mm surface mount footprint and has full FCC and CE module certification. This product is targeted for low cost embedded wireless applications and enables a quick, easy and cost effective method adding WiFi connectivity to your platforms. A summary of the key module features:

  • 802.11 b/g/n Compatible based on Broadcom MAC/Baseband/Radio device.
  • Fully contained TCP/IP stack thus minimizing host CPU requirements
  • Configurable though AT commands.
  • Host interface:  UART, SPI up to 25 MHz
  • Network features ICMP ( Ping), ARP, DHCP,TCP, UDP
  • Low power operation (3.3V supply) with built-in low power modes.
  • Secure WiFi authentication WEP-128, WPA-PSK (TKIP), WPA2-PSK 

Product Documentation

Technical Resources

Product Resources

Firmware

Software Scripts Examples

Embedded Talk Video’s

Evaluation Board Options:

Evaluation Board (Part number: ISM43362-M3G-EVB-E) – Standard evb with break out headers for L44 pins
ISM43362-M3G-EVB

Evaluation Board Shield:

ISMART (Inventek Systems Module Arduino Test) IoT platform ISMART43340-C Arduino Shield
ISM43340C Shield part

Buy Online from Our Valued Distributors

Buy Inventek products from DigiKey
Buy Inventek products from Texim Europe
Buy Inventek products from Macnica Store

Contact Inventek

Contact us for Sales Support Volume Pricing & Delivery options
Contact Inventek

ISM43903-R48-L54-E/U Serial-to-WiFi Module

The ISM43903-R48-L54-E/U is an embedded 2.4 GHz Wi-Fi module. The Wi-Fi module hardware consists of a Cypress 43903 SOC with ARM Cortex-R4 clocked at 160 MHz (in 1× mode) or up to 320 MHz (in 2× mode), an integrated antenna or optional external antenna, 1 MB of SRAM and 640 KB ROM available for the applications processor, SPI or UART interface capability.

The Wi-Fi module requires no operating system and has an integrated TCP/IP stack that only requires a simple AT command set to establish connectivity for your wireless product. The module has a very small 14.5mm x 30mm surface mount footprint and has full FCC and CE module certification (In process). This product is targeted for low cost embedded wireless applications and enables a quick, easy and cost effective method adding WiFi connectivity to your platforms.

A summary of the key module features

  • ARM Cortex-R4 clocked at 160 MHz (in 1× mode) or up to 320 MHz (in 2× mode).
  • 1 MB of SRAM and 640 KB ROM available for the applications processor.
  • One high-speed 4-wire UART interface with operation up to 4 Mbps.
  •  Two low-speed 2-wire UART interfaces multiplexed on general purpose I/O (GPIO) pins.
  • SPI master/slave interfaces with operation up to 24 MHz
  • U.FL Connector for external 2.4 GHz Antenna
  • Configurable using AT commands (IWIN)
  • Host interface: UART
  • 44-Pin and L44+10 Land Grid Array Footprint
  • 14.5mm x 30mm x 2.5 mm
  • 17 GPIO’s
  • Input Voltage: 3.3 V
  • Low power operation with built-in low power modes.
  • 802.11 b/g/n Compatible based on Broadcom MAC/Baseband/Radio device.
  • Fully contained TCP/IP stack thus minimizing host CPU requirements
  • Network features ICMP ( Ping), ARP, DHCP,TCP, UDP
  • Low power operation (3.3V supply) with built-in low power modes.
  • Secure WiFi authentication WEP-128, WPA-PSK (TKIP), WPA2-PSK 

Product Documentation

Technical Resources

Product Resources

Software Scripts Examples

Embedded Talk Video’s

Evaluation Board Detail

ISM43362-M3G-EVB
Evaluation board ISM43362-M3G-EVB-E

Applications

  • PDA, Pocket PC, computing devices
  • Building automation and smart energy control.
  • Industrial sensing and remote equipment monitoring.

Contact Inventek

For sales support Volume Pricing and delivery options
Contact Inventek

Buy Online from Our Valued Distributors

Buy Inventek products from DigiKey
Buy Inventek products at Avnet
Buy Inventek products from Texim Europe
Buy Inventek products from Macnica Store

Buy Online at Inventek Store

Buy Online

ISM43907-WM-L170 Serial-to-WiFi Module

The ISM43907-WM-L170 is an embedded 2.4 & 5.0 GHz Wi-Fi module. The Wi-Fi module hardware consists of a Cypress 43907 SOC with ARM Cortex-R4 clocked at 320 MHz, 2 MB of SRAM and 640 KB ROM, all clocks, T/R switch and duplexer available for the applications processor, SPI or UART interface capability.

The Wi-Fi module requires no operating system and has an integrated TCP/IP stack that only requires a simple AT command or the Cypress WICED SDK set to establish connectivity for your wireless product. The module has a very small 11 mm x 11 mm surface mount footprint and has full FCC and CE module certification (In process). This product is targeted for low cost embedded wireless applications and enables a quick, easy and cost effective method adding WiFi connectivity to your platforms.

Summary of the key features for this wifi module

  • ARM Cortex-R4 clocked at 160 MHz (in 1× mode) or up to 320 MHz (in 2× mode).
  • 2 MB of SRAM and 640 KB ROM available for the applications processor.
  • One high-speed 4-wire UART interface with operation up to 4 Mbps.
  •  Two low-speed 2-wire UART interfaces multiplexed on general purpose I/O (GPIO) pins.
  • SPI master/slave interfaces with operation up to 24 MHz
  • Configurable using AT commands (IWIN) or WICED
  • Host interface: UART or SPI
  • 11mm x 11mm x 1.2 mm
  • 17 GPIO’s
  • Input Voltage: 3.3 V
  • Low power operation with built-in low power modes.
  • 802.11 b/g/n Compatible based on Broadcom MAC/Baseband/Radio device.
  • Fully contained TCP/IP stack thus minimizing host CPU requirements
  • Network features ICMP ( Ping), ARP, DHCP,TCP, UDP
  • Low power operation (3.3V supply) with built-in low power modes.
  • Secure WiFi authentication WEP-128, WPA-PSK (TKIP), WPA2-PSK 

Product Documentation

Technical Resources

Contact Inventek

For sales support Volume Pricing and delivery options
Contact Inventek

Buy Online at Inventek Store

Buy Online

ISM4343-M4G-L54 Wi-Fi / BT Combo Module

The ISM4343-M4G-L54 is an embedded 2.4 GHz  Wi-Fi and Bluetooth combo module. The module hardware consists of the Cypress CYW4343 radio and ST Micro STM32F412 Cortex MCU.

The Wi-Fi module requires no operating system and has an integrated TCP/IP stack that only requires a simple AT command or the Cypress WICED SDK set to establish connectivity for your wireless product.

The ISM4343-M4G-L54 is an embedded Serial WiFi (eS-WiFi), wireless internet connectivity module that operates in the 2.4GHz spectrum.  The eS-WiFi module’s hardware consists of an ARM Cortex M4 host processor, Cypress CYW4343 Single-Band (2.4GHz) 802.11 /b/g/n MAC/Baseband/Radio with Integrated Bluetooth 4.2.

Inventek’s IWIN, AT command set, allows you to quickly establish connectivity for your wireless product, minimizing development time, testing routines and certification. The low cost, small foot print (14.5 mm x 34 mm) and ease of design-in make it ideal for a range of embedded applications.

Uses CYW4343 Cypress Leading Edge Radio Device

  • Includes STM32F412 ST Cortex M4 Microcontroller with 1MB of on board Flash.
  • 2.4 GHz Wi-Fi Band.
  • Bluetooth 4.1 including BLE Support.
  • 2 MB Flash, Xtal, Low Pass filter , 2.4GHz Chip Antenna on the eS-WiFi module
  • Optional U.FL Connector for external 2.4 GHz Antenna
  • Configurable using Inventek proprietary IWIN AT commands.
  • Host interface: UART, SPI
  • 54 Land Grid Array Footprint (7 GPIO for IWIN & 17 GPIO for WICED).

Product Documentation

Contact Inventek

For sales support Volume Pricing and delivery options
Contact Inventek

ISM4343-WBM-L151 Wi-Fi / BT Combo Module

The ISM4343-WBM-L151 is an embedded 2.4 GHz Wi-Fi and Bluetooth combo module. The module hardware consists of the Cypress CYW4343 radio and ST Micro STM32F412 Cortex MCU.

The Wi-Fi module requires no operating system and has an integrated TCP/IP stack that only requires a simple AT command or the Cypress WICED SDK set to establish connectivity for your wireless product.

The module has a very small 10 mm x 10 mm surface mount footprint and will have FCC and CE module certification (In process). This product is targeted for low cost embedded wireless applications and enables a quick, easy and cost effective method adding Wi-Fi connectivity to your platforms. A summary of the key module features:

WLAN, Bluetooth & MCU functions:

  • Single-band 2.4 GHz b/g/n, 802.11b, 802.11g, 802.11n (single stream)
  • STM32 ARM 32-bit CortexTM-M4 with a frequency up to 100 MHz.
  • 1 Mbyte of MCU internal Flash
  • 256KB of SRAM
  • SPI, Quad SPI (support Dual mode), USART, PCM
  • ADC, I2C, I2S, GPIO, Timers
  • JTAG
  • Bluetooth v4.1 with integrated Class 1 PA
  • Bluetooth 2.1+EDR, Buletooth 3.0, Bluetooth 4.1 (Bluetooth Low Energy)
  • Bluetooth v4.2 LE Secure Connection via the Cypress BSA stack.

Product Documentation

Contact Inventek

For sales support Volume Pricing and delivery options
Contact Inventek

ACTPAT184-01-IP GPS Antenna

Inventek’s 18.6 mm x 18.6 mm x 7 mm GPS ceramic active antenna is designed to connect directly to the ISM300x GPS receivers or we can support any GPS receiver connector type for special orders.

Center Frequency 1.575 GHz, 3-5 VDC, with gain of 28 dB at 3 volts. Standard parts comes with a 2.5 inch mini cable and IPEX U.FL connector. Lead free, RoHS compliant.

Product Specifications

*Custom cable length and connectors available. For a custom cable, a minimum order of 500 units is required.

Benefits

  • Ideal for compact size devices
  • The elimination of RF board design
  • Easy integration
  • Connects directly on top of the ISM300Fx family of receivers

Applications

This antenna is designed for quick and easy integration into GPS-related applications – especially compact size devices – such as:

  • Hand-held Devices for Personal Positioning and Navigation
  • PDA, Pocket PC and other computing devices
  • Fleet Management / Asset Tracking
  • AVL and Location-Based Services

Buy Online from Our Valued Distributors

Buy Inventek products at Avnet
Buy Inventek products from Texim Europe

Contact Inventek

Contact Inventek

Wi-Fi 2.4/ 5GHz, Bluetooth & BLE SiP Module

The ISM43340-L77 quad-radio device provides the highest level of integration for wireless system, with integrated dual band (2.4 GHz/ 5 GHz) IEEE 802.11 a/b/g/n single-stream, MAC/baseband/radio, Bluetooth 4.0.

Product Specifications

The ISM43340 includes integrated power amplifiers, LNAs and T/R switches for the 2.4 GHz and 5 GHz WLAN bands, greatly reducing the external part count, PCB footprint, and cost of the solution.

This product is intended for embedded Linux/ Android applications running on qualified Host processors with a SDIO interface. This product is targeted at high volume designs with experienced Linux / Android customers. A Software License Agreement is required for Driver support.

Product Overview

  • Wi-Fi standards, speeds and security:
    • 802.11 a/b/g/n with speeds up to 72Mbps
    • WEP(64/128-bit), WPA, WPA2 (Personal), 802.11i (AES, TKIP, 802.1x)
  • System-in-Package design, no need for external crystal oscillators or RF switches
  • Single supply voltage of 3.3VDC ±5%
  • 77 pin LGA package (13.3mm x 14.5 mm, 2 mm)
  • WLAN, Bluetooth functions:
    • Shared Single and dual-antenna support
    • WLAN host interface :4-bit SDIO for easy host interfacing
    • BT host digital interface (can be used concurrently with above interface): UART (up to 4 Mbps)
    • ECI – enhanced coexistence support, ability to coordinate BT SCO transmissions around WLAN receives
    • I²S/PCM for BT audio
    • HCI high-speed UART (H4, H4 +, H5) transport support
    • Bluetooth SmartAudio® technology improves voice and music quality to headsets
    • Bluetooth low power inquiry and page scan
    • Bluetooth Low Energy (BLE) support
    • Bluetooth Packet Loss Concealment (PLC)
    • Bluetooth Wide Band Speech (WBS)

Radio Only SIP Summary

340 431 SIP driver details

Evaluation Boards

Rocky Mini ISM43341-L77 EVB
ISM43340-L77-EVB

Applications & Uses

  • Internet Enabled Consumer Devices
  • M2M (Machine-to-Machine)
  • Industrial Handheld Devices
  • Asset/Inventory Management
  • POS Terminals
  • Medical Equipment
  • Wi-Fi Enabled Security Cameras

Contact Inventek

We are looking forward to answering all your inquiries regarding sales, technical and customer support, distribution volume pricing and delivery options
Contact Inventek

GPS Waterproof Active Antenna (SMA) – Magnetic

Waterproof Active Antenna (with magnet) for ISM300x GPS recievers or any GPS receiver

Description

Active GPS dome antenna with 5 meter cable with SMA connector. The antenna is waterproof, magnetic and is designed to work with a variety of GPS receivers. 1.575 GHz, 50 ohms, 3-5 VDC and a gain of 30 dB at 3.0 volts.

GPS Waterproof Active Antenna Dome (PDF)

Contact Inventek

Contact us for Volume Pricing & Delivery
Contact Inventek

ISM43362-M3G-EVB-E Wi-Fi Evaluation Board

The ISM43362-M3G-EVB-E is an embedded wireless evaluation board that is used to evaluate the  802.11 b/g/n eS-Wi-fi embedded module. The evaluation board consist of a Wi-Fi module with host processor, integrated etch antenna and Broadcom Wi-Fi device, supported by WICED. Simply install the USB drivers and you can immediately run the Inventek AT commands to communicate with eS-WiFi or Broadcom WICED SDK.

The evaluation kit comes with USB cable, ISM43362-M3x-L44-E, Demo software, drivers, CD, sensor board with temperature sensor, LED’s and switches.  USB powers the entire board and you have an option to power the unit with an external DC input. A summary of the kit features:

  • 802.11 b/g/n Compatible based on Broadcom BCM43362 MAC/Baseband/Radio device.
  • Fully contained TCP/IP stack thus minimizing host CPU requirements
  • Configurable though AT commands.
  • Network features ICMP ( Ping), ARP, DHCP,TCP, UDP
  • Secure WiFi authentication WEP-128, WPA-PSK (TKIP), WPA2-PSK

EVB Product Documentation

EVB Product Resources

ISM43362-M3G-EVB-E

Buy Online from Our Valued Distributors

Buy Inventek products from Texim Europe
Buy Inventek products at Arrow Electronics
Buy Inventek products from Macnica Store

Buy Online at Inventek Store

Buy Online at Inventek Store

Contact Inventek

Contact us for Sales Support Volume Pricing & Delivery options
Contact Inventek

ACTPAT182-XX-IP GPS Antenna

Inventek’s 18.6 mm x 18.6 mm x 4.9 mm active antenna is designed to connect directly to the ISM300Fx GPS receivers or we can support any GPS receiver connector type for special orders.

Center Frequency 1.575 GHz, 3-5 VDC, with gain of 28 dB at 3 volts. Standard parts comes with a 2.5 inch mini cable and IPEX U.FL connector. Lead-free, RoHS compliant.

Product Specifications

*Custom cable length and connectors available. For a custom cable, a minimum order of 500 units is required.

Benefits

  • Ideal for compact size devices
  • The elimination of RF board design
  • Easy integration
  • Connects directly on top of the ISM300Fx family of receivers

Applications

This antenna is designed for quick and easy integration into GPS-related applications –  especially compact size devices – such as:

  • Hand-held Devices for Personal Positioning and Navigation
  • PDA, Pocket PC and other computing devices
  • Fleet Management / Asset Tracking
  • AVL and Location-Based Services

Buy Online at Inventek Store

Buy 18mm x 18mm x 4.9mm Active GPS Antenna Online

Buy Online Through our valued Distributors

List of Inventek Product Distributors

Contact Inventek

Contact Inventek

ISM43340-M4G-EVB-C Wi-Fi & Bluetooth Combo Evaluation Board

The ISM43340-M4G-EVB-E is an embedded wireless evaluation board that is used to evaluate the  802.11 b/g/n eS-Wi-fi and Bluetooth 4.0  embedded module. The evaluation board consist of a Wi-Fi module with host processor, integrated  antenna and Broadcom Wi-Fi device, supported by WICED. Simply install the USB drivers and you can immediately run the Inventek AT commands to communicate with eS-WiFi or you can install WICED.

The evaluation kit comes with USB cable, ISM43340-M4G-L44-E, Demo software, drivers, CD, sensor board with temperature sensor, LED”s and switches. USB powers the entire board and you have an option to power the unit with an external DC input. A summary of the kit features can be found here: EVB Technical Support

ISM43362-M3G-EVB-E

Contact Inventek

Contact us for Sales Support Volume Pricing & Delivery options
Contact Inventek

Buy Online from Our Valued Distributors

Buy Inventek products at Arrow Electronics

USB CABLE – Type A Plug – Mini B Plug

USB Cable, 20 inches long USB Type A plug to mini B plug. Use to transfer data and charge USB device

Wi-Fi 2.4 Ghz PCB Antenna (P/N W24P-U)

The W24P-U Wi-Fi PCB antenna 2400-2500 Mhz (30 x 5 mm) with U.fl connector, let’s you integrate Wi-Fi functionality into your product quickly and easily. It’s suitable for a wide range of applications and recommended for use with Inventek eS-Wi-Fi modules.

Product Specification

Benefits

Wi-Fi antenna is designed to connect to the eS-Wi-Fi family of modules. This antenna has also passed complete FCC, CE and IC certification using the Inventek eS-Wifi modules.

  • Stable and reliable in performances
  • PCB antenna has excellent sensitivity to consistently provide high signal reception efficiency
  • Compact size
  • RoHS compliance

Buy Online from Our Valued Distributors

Buy Inventek products from DigiKey
Buy Inventek products at Avnet

Buy Online at Inventek Store

Buy Online at Inventek Store

Contact Inventek

For sales technical support distribution Volume Pricing and delivery options
Contact Inventek

ACTPAT254-01-IP GPS Antenna

Inventek’s 25 mm x 25 mm x 8.3 mm GPS ceramic active antenna is designed to connect directly to the ISM300x GPS receivers or we can support any GPS receiver connector type for special orders.

Center Frequency 1.575 GHz, 3-5 VDC, with gain of 26 dB at 3 volts. Standard parts comes with a 2.5 inch mini cable and IPEX U.FL connector. RoHS compliant.

Product Specifications

*Custom cable length and connectors available. For a custom cable, a minimum order of 500 units is required.

Benefits

  • Ideal for compact size devices
  • The elimination of RF board design
  • Easy integration
  • Connects directly on top of the ISM300Fx family of receivers

Applications

This antenna is designed for quick and easy integration into GPS-related applications –  especially compact size devices – such as:

  • Hand-held Devices for Personal Positioning and Navigation
  • PDA, Pocket PC and other computing devices
  • Fleet Management / Asset Tracking
  • AVL and Location-Based Services

Buy Online from Our Valued Distributors

Buy Inventek products from DigiKey
Buy Inventek products at Avnet

Buy Online at Inventek Store

Buy 25 mm x 25 mm Active GPS Antenna Online

Contact Inventek

Contact Inventek

ISMART Arduino Shields – Wi-Fi & Bluetooth & NFC

The ISMART (Inventek Systems Module Arduino Test) IoT platform is a user-friendly Arduino and ST Micro ST NUCLEO compliant shield suited for all of your wireless application needs.

The ISMART shield is an embedded wireless internet connectivity platform that operates in the 2.4 & 5.0 GHz spectrum. The ISMART hardware includes the option for  an Inventek eS-WiFi module consisting of the Broadcom BCM43362 (2.4GHz), or BCM43341/0 Dual-Band (2.4GHz / 5GHz) 802.11 a/b/g/n MAC/Baseband/Radio with Integrated Bluetooth 4.0 and NFC. 

The ISMART shield interfaces with the ST Micro NUCLEO boards and is compatible with the Arduino UNO R3 connector layout (without software support for Arduino). The Wi-Fi module requires no operating system and contains an integrated TCP/IP stack. The module hardware can be used with Inventek’s AT Command set (IWIN) or with Broadcom’s WICEDTM SDK. ISMART Hardware Users Manual

Hardware Features

Uses the Inventek ISM43341/0 or ISM43362 eS-WiFi modules leveraging Broadcom’s leading edge radio devices.

Includes an ST Microcontroller Cortex M3 STM32F204 (ISM43362) or Cortex M4 STM32F405 (ISM43341/0), MCU.

  • Bluetooth 4.0 including BLE support.
  • 2.4GHz (ISM43362) or 2.4/5 GHz (ISM43341/0), chip antenna on module.
  • U.FL external antenna connector option for both modules
  • Configurable using Inventek AT Commands FW (IWIN).
  • Host interface: UART, SPI.
  • Input Power: 5.0 V
  • Near Field Communication (NFC option), with the ISM43341 modules.
  • Dual Port FTDI for firmware development and testing.
  • SPI Flash for Over The Air (OTA) updates
  • FCC, IC and CE approval on all module options.
  • All eS-WiFi module options also support a standard L44 or L44 +10 form factor to enable customers to migrate between module options once in mass production without requiring any board layout changes.

ISM43340C Shield part

Product Documentation

Technical Resources

Software Scripts Examples

Product Resources

Firmware

Buy Online at Inventek Store

Buy Online

Contact Inventek

For sales technical support Volume Pricing and delivery options
Contact Inventek

MCX – GPS Antenna – 10 Meter cable

Waterproof Active Antenna (with magnet) for ISM300x GPS recievers or any GPS receiver

Product Description

Active GPS dome antenna with 5 meter cable with SMA connector. The antenna is waterproof, magnetic and is designed to work with a variety of GPS receivers. 1.575 GHz, 50 ohms, 3-5 VDC and a gain of 30 dB at 3.0 volts.

MCX – GPS Antenna – 10 Meter cableSpecs

GPS Waterproof Active Antenna Dome(PDF)

Contact Inventek

For sales technical support Volume Pricing and delivery options
Contact Inventek

Wi-Fi Antenna 2.4 Ghz Right Angle SMA Male (P/N W24-RSMA-M)

The W24-RSMA-M Wi-Fi antenna 2400-2500 Mhz  Right angle sma male (46.5 mm long) with a gain (dBi) of 2.15. It’s suitable for a wide range of Wi-Fi applications and recommended for use with Inventek eS-Wi-Fi modules.

Product specification

W24-RSMA-M Functional Specification – Inventek’s Wi-Fi antenna is designed to connect to the eS-Wi-Fi family of modules. This antenna has also passed complete FCC, CE and IC certification using the Inventek eS-Wifi modules.

  • Stable and reliable in performances
  • The  antenna has excellent sensitivity to consistently provide high signal reception efficiency
  • Compact size
  • RoHS compliance

Buy Online from Our Valued Distributors

Buy Inventek products from DigiKey
Buy Inventek products at Avnet
Buy Inventek products at Arrow Electronics
Buy Inventek products from Texim Europe

Buy Online at Inventek Store

Buy Online at Inventek Store

Contact Inventek

For all your inquiries regarding sales, technical and customer support, distribution volume pricing and delivery options
Contact Inventek

ANTDOM-05-01-WPM GPS Antenna

Active GPS dome antenna with 5 meter cable with SMA connector. The antenna is waterproof, magnetic and is designed to work with a variety of GPS receivers. 1.575 GHz, 50 ohms, 3-5 VDC and a gain of 30 dB at 3.0 volts.

Product Specifications

*Custom cable length and connectors available. For a custom cable, a minimum order of 500 units is required.

Benefits

  • Ideal for compact size devices
  • The elimination of RF board design
  • Easy integration
  • Connects directly on top of the ISM300Fx family of receivers

Applications

This antenna is designed for quick and easy integration into GPS-related applications – such as:

  • Hand-held Devices for Personal Positioning and Navigation
  • PDA, Pocket PC and other computing devices
  • Fleet Management / Asset Tracking
  • AVL and Location-Based Services

Contact Inventek

Contact Inventek

Buy Online from Our Valued Distributors

Inventek Products Distributor List

Wi-Fi 2.4/ 5GHz, Bluetooth & BLE EVB

The ISM43340-L77-EVB evaluation board offers 802.11 Wi-Fi connectivity over an SDIO interface, as well as Bluetooth over a UART interface. The combo radio is targeted at embedded Linux applications or virtual Broadcom WICED.

Evaluation Kit Product Overview

  • Wi-Fi standards, speeds and security:
    • 802.11 a/b/g/n with speeds up to 72Mbps
    • WEP(64/128-bit), WPA, WPA2 (Personal), 802.11i(AES, TKIP, 802.1x)
  • System-in-Package design, no need for external crystal oscillators or RF switches
  • Single supply voltage of 3.3VDC ±5%
    • WLAN host interface :4-bit SDIO for easy host interfacing
    • BT host digital interface UART (up to 4 Mbps)

Product Specifications

This product is intended for embedded Linux and Android applications running on qualified Host processors with a SDIO interface. This product is targeted at high volume designs with experienced Linux/Android customers. A Software License Agreement is required for Driver support.

Radio Only SIP Summary

340 431 SIP driver details

Rocky Mini ISM43341-L77 EVB

evaluation board

Contact Inventek

Simply contact us for more supported processors, sales, technical and customer support, distribution Volume Pricing and delivery options
Contact Inventek

Pages: 1 2 3Next >Last »